Section 1 - Jobsite Preparation and Equipment Staging

• 1.1 Peelle Company Contact Information
• 1.2 Introduction
• 1.3 Unpacking/Reviewing Materials
• 1.4 Tool List

Section 2 - Frame Installation

• 2.1 Frame Criteria
• 2.2 Installing the Sill
• 2.3 Installing the Sill
• 2.4 Installing the Sill
• 2.5 Installing the Jambs (Side Members) and Head of Frame

Section 3 - Rail Installation

• 3.1 Materials
• 3.2 Rail Installation Summary
• 3.3 Determine Best Horizontal Location for Rails on the Flange of the Vertical Jambs
• 3.4 Identify Type of Rails Being Used
• 3.5 Identify Vertical Sill Mark
• 3.6 Verify Door Gauge Rod for Distance Between Guides (DBG) is correct length
• 3.7 Install First Rail ("King Rail") [Interlock Side]
• 3.8 Install Opposite Rail ("Queen Rail") [Side opposite the interlock]
• 3.9 Install Second King Rail
• 3.10 Mount Operators/ Sheaves
• 3.11 Mount Door Rail Junction Boxes and DOFL Limit Switches

Section 4 - Door Hanging

• 4.1 Door Installation Summary
• 4.2 Hang Door Chains
• 4.3 Secure Chain Fall at Top of Shaft
• 4.4 Install Lower Door Panel
• 4.5 Install Upper Door Panel
• 4.6 Mount Tension Latches
• 4.7 Attach Chains and Level Upper Door Panel
• 4.8 Install Door Interlock
• 4.9 Door Interlock Installation
• 4.10 Tension Latch Adjustment
• 4.11 Install Tamper Resistant Plugging Rod
• 4.12 Adjust Contact Arm Cam
• 4.13 Install Door Unlocking Device
• 4.14 Install Anchors and/or Spreaders for each Pair of Rails
• 4.15 Mount Limit Faceplate

Section 5 - Cab Enclosure

• 5.1 Cab Enclosure Installation Summary
• 5.2 Fasten Bottom Angles to Car Platform
• 5.3 Assemble Right Side Wall of Cab Enclosure
• 5.4 Assemble Back Wall of Cab Enclosure
• 5.5 Assemble Left Side Wall of Cab Enclosure
• 5.6 Attach Top Support Angles
• 5.7 Assemble Top of Cab Enclosure
• 5.8 Attach Stile Steadying Plate
• 5.9 Plumb Cab Enclosure Walls
• 5.10 Install Cab Lights, Bumpers, Fan
• 5.11 Engage Emergency Exit Contact Switch

Section 6 - Gate Installation

• 6.1 Car Gate Installation Summary
• 6.2 Fasten Gate Rails to Cab Enclosure
• 6.3 Install Cross Braces from Top Gate Spreader Angle to Gate Rails
• 6.4 Install Cross Braces from Car Gate to Car Cross Head
• 6.5 Install Counterweight
• 6.6 Install Gate Operator
• 6.7 Fasten Gate Chains
• 6.8 Install Gate Panel(s)
• 6.9 Install the Retiring Cam Assembly
• 6.10 Install Limit Switches
• 6.11 Set Door and Gate Limits
• 6.12 Install Gate Contact
• 6.13 Install Light Curtain
• 6.14 Adjust Interlock Roller Arms to be Fully Depressed by Retiring Cam Face
  

Section 7 - Controller Installation

• 7.1 Wiring Package (Optional)
• 7.2 Controller & Wiring Installation Summary
• 7.3 Mount Controller Enclosure in Elevator Machine Room
• 7.4 Mount Center Junction Box in Hoistway
• 7.5 Pipe Hoistway and Cab Enclosure
• 7.6 Mount Top of Cab Junction Box
• 7.7 Pull Peelle Bundle Wire Through Conduit
• 7.8 Phase Door Motors
• 7.9 Phase Retiring Cam Motor
• 7.10 Phase Gate Motor
• 7.11 Adjust Door Sensor Limits
• 7.12 Adjust Gate Sensor Limits
• 7.13 Check Interlocks for Continuity
• 7.14 Check Gate Contact for Continuity
• 7.15 Test Light Curtain/Reversing Edge
• 7.16 Check for Door Automatic Stay Open (ASO) (Optional)
• 7.17 Adjust GCT & ACT Timers
• 7.18 Fasten All Covers
• 7.19 Sequence of Operation
• 7.20 Controller Features